Print this page

 

What You Should Know About White Light vs Blue Light 3D Scanning Technologies

Quick Links Menu

  1. White light vs. blue light introduction
  2. What is white light scanning?
  3. What is blue light scanning?
  4. Use case: Extending the life of C130 Aircraft
  5. Use case: How AMRDEC saved up to $100 million with blue light 3D scanners 
  6. Conclusion

KEY TAKEAWAY: The main benefit of blue light 3D scanners over white light 3D scanners is typically higher accuracy and resolution in capturing surface details, particularly on reflective or dark-colored surfaces.

 

3D scanning is an important part of quality assurance, prototyping, manufacturing, and reverse engineering. The precise 3D blueprints and rapid workflows enabled by light-based non-contact metrology solutions make them an important technology that can have measurable benefits on an organization's bottom line.

However, many organizations are unfamiliar with the details of the various 3D scanning technologies available, and what you don’t know can hurt you.

As industry standards progress, competition ramps up, and regulations become more and more stringent, it becomes more and more important for organizations to understand technologies that can position them the most advantageously in the marketplace.

One area of confusion related to the 3D scanning industry is the difference between white light vs blue light scanning.

While the short answer is blue light scanning is the more modern and advanced version of the two technologies, the topic warrants further discussion to help build a better understanding of how the technologies can benefit you.

In this article, we will provide an introduction to white light and blue light scanning, compare white light vs blue light scanning and dive into some use cases for the technology (including how AMRDEC saved up to $100 million with ATOS blue light 3D scanners).

 

What is white light scanning? blog white lighbulb 1

White light 3d scanning is a type of non-contact metrology that leverages white light to produce highly accurate measurements.

White light scanning enables highly accurate 3D models of physical objects to be created quickly and with a high level of precision. White light scanning technology has been on the market for over two decades.

GOM’s ATOS systems, which have since evolved to utilize the more advanced blue light technology, were using white light commercially as early as 1995.

White light 3D scanning works by projecting the line shadows from a 2D lens to a 3D surface.

Cameras are then leveraged to view the variances in the 2D lines on the 3D objects and use advanced algorithms to generate point clouds.

The X-Y-Z coordinate points generated during this process are then brought together to create a precise 3D model of the physical object

When compared to traditional laser scanning, white light 3d scanning can offer a number of benefits.

Laser scanners use laser beams to measure the surface area of a device and create models based on that data. Oftentimes the process of collecting measurements using a laser-based system can be tedious and labor-intensive.

Laser measurement systems often require the user to leverage a portable 3d scanner or articulating arm and wave the scanner in a paintbrush-style motion over the object.

Not only can this process be time-consuming, but it can also lead to redundancy in efforts and overlapping data.

A white light-based 3D scanning system on the other hand generally uses a camera mount, tripod, or robot and enables a “point & shoot” style workflow that minimizes setup and programming.

Similarly, white light 3d scanning offers workflow advantages over traditional coordinate measuring machine (CMM) based scanning systems.

Traditional CMMs require that a probe touches an object’s surface in order for a measurement to be gathered. This means that as the complexity and size of an object scales, so can the measurements and programming required to use a CMM.

White light 3D scanning, a non-contact metrology method leveraging white light technology, facilitates the rapid and precise creation of highly accurate 3D models, offering workflow advantages over traditional laser scanning and coordinate measuring machine (CMM) systems.

 

What is blue light scanning? blog 3d measurement systems

When comparing white light vs blue light scanning, it can be easy to become confused as to the differences between the two technologies. Sorting through the differences can become even more difficult when you consider that some marketing materials and articles related to the topic of metrology seem to use the terms interchangeably.

In short, blue light scanning is an enhanced version of the white light technology discussed above. When comparing white light vs blue light scanning, they are known to be used in many of the same cases. However, blue light 3D scanners offer better precision, accuracy, and higher quality outputs.

One of the reasons blue light scanning technology is able to offer benefits over white light scanning technology is based on the fact that blue light has a narrower wavelength whereas white light is a combination of all the colors in the visible spectrum.

The narrow wavelength of blue light helps enable better filtering of interference from ambient light.

ATOS technology based on blue light scanning enables users to quickly generate 3D blueprints of physical objects with a high level of accuracy.

For example, the GOM ATOS Triple Scan which is capable of measuring up to 8 million points per scan won the GE High Accuracy, High Throughput Inspection Technologies Challenge where the objective was to inspect the blade of a Victorinox paring knife in under three minutes. Accuracy of the inspection had to be 10 microns or less with a repeatability of 5 microns. Despite the competition from 50 other entrants, with its advanced blue light technology, the ATOS Triple Scan was able to come out of the competition a winner.

This GOM ATOS Triple Scan has since been updated by the ATOS 5 and represents a significant advancement over the ATOS Triple Scan in terms of these factors:

  • tighter accuracy
  • faster scanning speed
  • increased measuring range
  • improved surface detection
  • ease of use
  • enhanced software integrations
  • reduced noise levels

These improvements make it a superior choice for demanding industrial metrology applications.

 

400X400.jpg

 

Use case: Extending the life of C130 Aircraft

While the aforementioned inspection of a blade portion of a Victorinox paring knife during the GE competition may seem like a novel exercise with a limited practical benefit at first glance, the reality is different.

The paring knife was used to serve as an affordable representation of a turbine blade. This makes sense when you consider the importance of highly accurate 3D models to the world of aviation.

A great example of the importance of 3D scanning and digital twin models in the aviation industry involves the ATOS 3D Scanner and TRITOP technology.

Canada’s National Research Council was tasked with a refurbishment project for aging C130 aircraft. As part of the project, they needed to update electrical and mechanical systems and develop 3D models for computational fluid dynamics (CFD) and stress analysis.

By partnering with Capture 3D, the National Research Council was able to have the required measurements completed in less than two weeks. Click here for more on this case study.

Use case: How AMRDEC saved up to $100 million with blue light 3D scanners

While the idea that blue light scanning can “improve workflows” may sound like marketing buzzwords as opposed to something that can impact your bottom line, the use of ATOS blue light 3D scanners by the US Army’s Aviation and Missile Research, Development and Engineering Center (AMRDEC) demonstrate the potential in a practical way.

AMDREC adopted ATOS blue light scanners as a standard for their “ inspection, reverse engineering and adaptive machining applications” and on one project alone the time savings enabled by the technology saved up to $100 million (source: advancedmanufacturing.org, May 15, 2017).

Click here to watch a video of ATOS and TRITOP in action scanning a 41-foot long Cost Guard boat at an AMDREC site in Redstone Arsenal, Alabama.

 

blog-blue-plexus_1.jpgConclusion

In conclusion, the comparison between white light and blue light scanning underscores the pivotal role of technological advancements in non-contact metrology.

While white light scanning boasts over two decades of market presence and facilitates quick and precise 3D model generation through the projection of line shadows onto surfaces, blue light technology, exemplified by GOM's ATOS systems, offers enhanced capabilities.

Blue light scanning enhances accuracy and efficiency, overcoming some limitations of white light systems.

Both technologies revolutionize quality control processes by minimizing setup time and streamlining workflows, ultimately optimizing manufacturing operations. As the industry evolves, understanding the nuances between white light and blue light scanning becomes imperative for manufacturers seeking to leverage cutting-edge metrology solutions.

Contact the experts

At this point, you may have some ideas about how blue light technology can benefit your business but are not sure where to start or what tools are right for you.  

Our dedicated team of experts at Capture 3D is ready and willing to help you find the right solution. Our solutions feature workflows that are optimized to specific industries and we specialize in helping you select the best solution for your unique use case. 

Contact us today to learn more!